Valves and solenoid valves (ISO 15407-1) Series 7
Size: 18 mm (VDMA 24563-02), 26 mm (VDMA 24563-01)
5/2 – 5/3-way CC CO CP
VDMA 24563 (ISO 15407-1)
5/2 – 5/3-way CC CO CP
VDMA 24563 (ISO 15407-1)
The Series 7 solenoid valves with ISO 26 mm and 18 mm interface which have electropneumatic actuation and return are suitable for mounting on a sub-base.
For electrical actuation, 2 types of solenoid Series W and Series P (available with a wide range of voltages, on request).
For electrical actuation, 2 types of solenoid Series W and Series P (available with a wide range of voltages, on request).
The Series 7 solenoid valves with ISO 26 mm and 18 mm interface which have pneumatic actuation and return are suitable for mounting on a sub-base.
For the correct use of the valve, the pilot pressure must be the same or higher than the operating pressure.
General Data
| Construction | Balanced spool type |
| Valve functions | 5/2 – 5/3-way CC CO CP |
| Materials | AL body, spool base, polyamide endcovers, NBR seals |
| Mounting | By means of screws on the base |
| Ports | On sub-base |
| Operating temperature | 0° C min. +50° C max |
| Fluid | Filtered air (5 micron or less), without lubrication. If lubricated air is used, it is recommended to use ISOVG32 oil. Once applied the lubrication should never be interrupted. |
| Size | 26 mm 18 mm |
| Installation | In any position |
| Operating pressure | P. max 7 bar |
| Nominal pressure | 6 bar |
| Nominal flow | Qn Size 26 mm = 900 Nl/min Qn Size 18 mm = 450 Nl/min |
| Voltage | See Coding example |
| Voltage tolerance | ± 10% |
| Power consumption | 2W |
| Class of insulation | Class F |
| Protection | IP54 (IP65 with connector DIN 40050) |
Coding Example
| 7 | 5 | 1 | – | N | 1 | A | – | P16 | – | 15 | – | W | 2 | 3 |
| 7 | SERIES |
| 5 | NUMBER OF WAYS – POSITIONS 5 = 5/2 6 = 5/3 CC 7 = 5/3 CO 8 = 5/3 CP |
| 1 | SIZES 1 = 26 mm 2 = 18 mm |
| N | SUBBASE N = Sub-base with front outlets |
| 1 | PORTS 1 = G1/4 (Size 26 mm) 2 = G1/8 (Size 18 mm) |
| A | NUMBER OF SUBBASES A = 1 * B = 2 * C = 3 * D = 4 * E = 5 * F = 6 * G = 7 * H = 8 * K = 9 * L = 10 * M = 11 * N = 12 * P = 13 * R = 14 * S = 15 * |
| P16 | ACTUATION 33 = Pneumatic, bistable 36 = Pneumatic, monostable P11 = Electro-pneumatic, bistable P16 = Electro-pneumatic, monostable |
| 15 | SOLENOID INTERFACE 15 = 15×15 |
| W | SOLENOID TYPES W = Series W (24V – 48V DC only) P = Series P ** |
| 2 | CONNECTION 1 = Wire 300 mm (Series W, 24V DC only) ** 2 = 2 Pins (Series W, 24V – 48V DC) 5 = 2 Pins+earth (Series P) ** |
| 3 | SOLENOID VOLTAGE 3 = 24V DC 4 = 48V DC ** 6 = 110V DC (with Series P solenoids only) ** B = 24V 50/60 Hz (with Series P solenoids only) ** C = 48V 50/60 Hz (with Series P solenoids only) ** D = 110V 50/60 Hz (with Series P solenoids only) ** |
* Complete with the two end blocks
** On request
** On request
RELATED PRODUCTS
Compact cylinders Tandem and Multi-position versions Series 32
Double-acting, magnetic
ø 25, 40, 63, 100 mm
Thanks to their great compactness Series 32 cylinders, Tandem and Multi-position, are suitable to be installed within confined spaces and can be used with the same mounting elements of other standard cylinders ISO15552.
The Tandem version enables to obtain up to 2 times the thrust force of a normal cylinder (standard traction force), while the Multi-position version can obtain up to three positions with one cylinder only.
Cylinders Series 40K
Double acting, cushioned, magnetic
Ø 160 - 200 - 250 - 320 mm
Series 40K cylinders comply with the ISO 15552 standard and can be assembled with the entire range of standard accessories.
A permanent magnet on the piston of these cylinders is able to send, through proximity switches mounted on the cylinder sliding axis, electrical signals to indicate its position.This series is normally equipped with end-stroke cushioning which can be adjusted through a screw on the end block.
Short-stroke cylinders Series RPA
Double-effect, magnetic
With hollow through rod and mounting stud
Bores: 20 and 30 mm
The Series RPA short stroke cylinders are double acting actuators with aluminium hollow through rod and mounting stud. Available in two sizes, Ø 20 and Ø 30 mm, with different strokes and dimensions of the mounting stud, these actuators are equipped with the non-rotating function of the rod.
The Series RPA are prepared for the mounting of magnetic sensors (Series CSD), in fact, on the external profile, along the cylinder tube, you can find sensor positioning slots.
Their compact and light design together with the adopted technical solutions make these cylinders suitable to be used, combined with suction pads, in End Of Arm Tooling (EOAT) systems, especially in the sector of plastic injection moulding.
Stainless steel cylinders Series 97
Single- and double-acting, cushioned, magnetic.
Ø 32, 40, 50, 63 mm
Series 97 stainless steel cylinders can be used in critical applications where a high level of corrosion resistance is required (for example: off-shore, naval, food industries).
These cylinders are normally equipped with end-stroke cushioning which can be adjusted through a screw on the end block.
In order to quieten the impact of the piston on the end block, these cylinders are also equipped with mechanical cushioning.
Stopper cylinders Series ST
Single and double-acting, magnetic, non-rotating
Sizes 20, 32, 40, 50 mm
The Series ST Stopper cylinders are pneumatic actuators with rod, complying with UNITOP and ISO 21287 standards, where rod and bushing have been specifically enlarged to ensure high resistance to radial loads and shocks.
These cylinders are available in two versions, double-acting and single-acting, and with rear spring.
The non-rotating rod version is also available.
The detection of the piston position is enabled by means of proximity switches (Mod. CST or CSH) which are mounted in slots along three sides of the cylinder profile.
It is possible to cover the slots with a proper profile (Mod. S-CST-500).
The high resistance to shocks and radial loads and the easy mounting makes Series ST particularly suitable for use in transport/conveyor lines where it is required to stop the transit of workpieces and workpiece-holder pallets.